Tehran University of Medical Sciences

Science Communicator Platform

Stay connected! Follow us on X network (Twitter):
Share this content! On (X network) By
Microtensile Repair Bond Strength of a Composite After Accelerated Artificial Aging: Effect of the Air Abrasion, Bur, Er:Yag Laser, Two-Step Self-Etch Bonding, and Universal Bonding Repair System Publisher



Rashidi M1 ; Berangi S2 ; Chiniforush N3 ; Ahmadi E4 ; Omrani LR5
Authors
Show Affiliations
Authors Affiliations
  1. 1. Department of Restorative Dentistry, Dental School, Kurdistan University of Medical Sciences, Sanandaj, Iran
  2. 2. School of Dentistry, Tehran University of Medical Sciences, Tehran, Iran
  3. 3. Laser Research Center of Dentistry (LRCD), Research Dentistry Institute, School of Dentistry, Tehran University of Medical Sciences, Tehran, Iran
  4. 4. Dental Research Center, Research Dentistry Institute, School of Dentistry, Tehran University of Medical Sciences, Tehran, Iran
  5. 5. Laser Research Center of Dentistry (LRCD), Dental Research Center, Research Dentistry Institute, School of Dentistry, Tehran University of Medical Sciences, Tehran, Iran

Source: Journal of Lasers in Medical Sciences Published:2022


Abstract

Introduction: Repair of old composite restorations is a conservative approach. This study sought to compare the effects of two adhesive systems on the bond strength of repaired composites prepared by three different surface treatments: erbium-doped yttrium aluminum garnet (Er:YAG) laser irradiation, air-abrasion, and bur preparation. Methods: Eight microhybrid (Polofil Supra, VOCO, Germany) composite resin blocks were fabricated. The blocks were aged and assigned to four groups as stated by the surface treatment: (I) air-abrasion (50 µ aluminum oxide particles), (II) diamond bur (fine grit), (III) Er:YAG laser (3 W output power, 300 mJ energy) and (IV) control. After surface treatment, the blocks were acid-etched and salinized. Each group was divided two subgroups, and the Clearfil SE Bond or All-Bond Universal was applied on their surface. Composite resin was bonded to the aged composites. The blocks were cut into eight samples, and the microtensile bond strength (MTBS) was measured. Results: The maximum MTBS was noted in the air-abrasion (25.1+6 MPa) group, followed by the Er:YAG laser (21.2+4.7 MPa). The mean MTBS in laser and air-abrasion groups was significantly higher than that in other groups (P<0.05). The mean MTBS was not significantly different between the laser and air-abrasion groups (P>0.05). Composite resin conditioning by All-Bond Universal in laser and air-abrasion groups yielded significantly higher MTBS than the Clearfil SE Bond (P<0.05). Conclusion: All surface treatments created acceptable bond strength. The surface treatment of the aged composite by the Er:YAG laser or air-abrasion along with the application of silane and All-Bond Universal provide high bond strength. © 2022,Suranaree Journal of Science and Technology. All Rights Reserved.
Related Docs
View other Related Docs
1. In Vitro Evaluation of Repair Bond Strength of Composite: Effect of Surface Treatments With Bur and Laser and Application of Universal Adhesive, Laser Therapy (2017)
2. Effect of Thermocycling and Surface Treatment on Repair Bond Strength of Composite, Journal of Clinical and Experimental Dentistry (2017)
3. Effect of Cold Plasma Spray on Microshear Bond Strength of Repair Composite Resin in Comparison With Other Surface Treatments, Journal of Adhesion Science and Technology (2021)
4. Repair Bond Strength of Composite: Effect of Surface Treatment and Type of Composite, Journal of Clinical and Experimental Dentistry (2018)
5. Effect of Plasma Radiation and Other Surface Preparation Methods on Microtensile Bond Strength of Repaired Aged Resin Composite, Frontiers in Dentistry (2023)
6. Surface Treatment Comparison by Application of Diamond Bur and Er,Cr:Ysgg at Different Powers: Morphological and Mechanical Evaluation, Laser Therapy (2016)
7. Repairability of Aged Dimethacrylate-Free Ormocer-Based Dental Composite Resins With Different Surface Roughening Methods and Intermediate Materials, Journal of Prosthetic Dentistry (2022)
8. Effect of Different Powers of Er, Cr:Ysgg Laser Treatment on Surface Morphology of Microhybride Composite Resin: Scanning Electron Microscope (Sem) Evaluation, Journal of Lasers in Medical Sciences (2015)
Experts (# of related papers)
View all Related Experts
Sedighe Sadat Hashemi Kamangar (3)
Sima Shahabi (2)
Other Related Docs
9. Comparative Efficacy of Er,Cr:Ysgg and Er:Yag Lasers for Etching of Composite for Orthodontic Bracket Bonding, Lasers in Medical Science (2018)
10. Scanning Electron Microscope (Sem) Evaluation of Composite Surface Irradiated by Different Powers of Er:Yag Laser, Journal of Lasers in Medical Sciences (2015)
11. Effects of Three Surface Conditioning Techniques on Repair Bond Strength of Nanohybrid and Nanofilled Composites, Dental Research Journal (2015)
12. Effect of Different Surface Treatments on the Long-Term Repair Bond Strength of Aged Methacrylate-Based Resin Composite Restorations: A Systematic Review and Network Meta-Analysis, BioMed Research International (2022)